Regina, Saskatchewan, Canada
Let the good times roll – Setting the standard in portable dock design since 1971
Roll-A-Dock is simply the fastest and easiest way to get full enjoyment from your waterfront property. In cold climates, there’s no need to endure frigid water – just roll it in and you’re ready for action.
Roll-A-Dock is ideally suited to gradual slopes and works equally well on soft or rocky bottoms. The roll in dock designs allows it to be easily placed using a vehicle or installed in a matter of minutes by as few as two people.
It is the ultimate portable dock ideal for your waterfront property. Easy Adjustment Over a Wide Range of Depths. A built-in winch with removable hand crank allows quick height adjustment for different depths or changing water levels. Adjustments are easily made without ever stepping into the water.
Standard Model adjusts from 2-1/2’ to 5-1/2’. Deep Water Kit adjusts from 2-1/2’ to 8’.4′ and 6′ Widths, Aluminum or Galvanized SteelWhile some portable docks are as narrow as 36”, Roll-A-Dock gives you the choice of 4’ or 6’ wide models – plenty of room for people to meet and pass.
Select all-aluminum construction for low weight and easy handling or galvanized steel for maximum strength.
Roll-A-Dock’s unique “V” type bracing reduces the clear span on a 32’ dock to only 21’. This design gives the wheel assembly superior strength both front and rear and assures maximum stability on soft or rocky bottoms.
With Roll-A-Dock’s exclusive connecting system, there is no loss of strength, even at the joints. The integrity of this design makes it possible to have a steel frame dock up to 32’ in length that requires no extra supports.
The Roll-A-Dock tapered frame incorporates design principles proven in bridge and rafter construction. This design provides maximum strength with a minimum of weight. The open sides of the frame also improve stability by reducing wave resistance.
The height adjusting winch is operated with a removable hand crank that is inserted in an opening in the deck surface. Height adjustments can be made while standing on the deck.
The height adjusting winch and cable is located inside the dock frame for greater safety. There are no exposed parts to snag – nothing to damage your boat when you pull along side.
Recommended for use on longer, multi-section docks over 48' long equipped with two or more wheel bases.
White Aluminum
Exceptional Engineering Redefines the Sectional Dock
Hewitt Classic Dock offers the great appearance and flexibility of a post and plank dock in a high-strength modular system. The Classic is perfect for people who want to make the most of their recreational time.
Large 4'x8’, 4’x12’, 4’x16’ sections mean fewer parts for faster installation.
Optional wheel kits are also available to aid placement and removal. Aluminum construction eliminates painting and requires little or no maintenance.
Modular design also makes it easy to add on or change the configuration of your dock at any time.
Pre-engineered components make installation a breeze with a 1/2” wrench the only tool needed for assembly. Dock sections are secured and adjusted for height with the turn of a bolt, and the 4’x4’ deck sections simply drop into place – no fasteners needed. For a streamlined appearance, poles may be cut flush with the deck surface.
Classic 4’x8’, 4’x12’, and 4’x16’ frame sections are extremely strong yet lightweight. Made from rugged 2”x5” double-wall extruded aluminum, the frames are reinforced with one center beam and two crossbars. Support poles, pads and fittings are also made from lightweight, corrosion-resistant aluminum.
Custom aluminum extrusion that allows other accessories to be mounted to the classic dock.
Custom aluminum extrusion that allows other accessories to be mounted to the classic dock.
Plastic plug fills open corner pocket of dock for a clean look.
Corners have changed to a heavy wall tube with a tapped set screw. Sides and ends have changed to a new extrusion to accept accessories.
Mud pad that slides on the axle of an upright wheel or screw legs.
White Aluminum
Cedar
Economical modular post-and-plank system
Hewitt Sectional Dock Systems offer greater economy, quick setup and minimal maintenance. Frames and decking are pre-assembled in easy-to-handle modules.
The aluminum sides wrap around the decking to maintain a crisp, clean appearance. Dock sections are 8’ and 10’ long and come in both 4’ and 6’ widths.
Sections may be joined end-to-end or turned at right angles to form “L”s, “T”s, and platforms.
Frames, poles and brackets are all made from rustproof, corrosion-resistant aluminum and never need painting.
Heavy-duty aluminum post brackets are bolted on for superior strength.
Aluminum side rails assure high strength and stability for a lifetime of service. Decking is fitted into a continuous channel on both sides and mechanically fastened for better support.
Complete the look with optional aluminum end caps for section ends.
Cedar Dock Sections
Aluminum Dock Sections
Leading edge of dock innovation-Introducing the UltraDock
Need a tough dock like the Hewitt Roll-A-Dock but don’t have the beachfront to roll it in for seasonal storage? Check out the new UltraDock from Hewitt.
Like the Roll-A-Dock, the UltraDock frame is made from tube construction for the ultimate structural support and superior clean lines. It can also be quickly disassembled and tucked away for the winter without taking up a large amount of space.
UltraDock’s modular design makes adding on or changing the configuration easy. Choose from three sizes: 4’x8’, 4’x12’and 4’x16’. Adjustable screw legs available in sizes ranging from small 24” to 34”, medium 36” to 50” and large 54” to 87”. 4’x8’ sundecks available to make platforms and large sun deck.
Aluminum
Aluminum Wood Grain
Prairie Leisure